Locally resolved stress measurement in the ultra-hard composites polycrystalline diamond and polycrystalline cubic boron nitride

verfasst von: Bernd Breidenstein, Nils Vogel
Abstract: Cutting tools made of the ultra-hard composites polycrystalline diamond and polycrystalline boron nitride are being used in more and more sectors of machining. Due to the laborious preparation processes such as grinding, brushing, electrical discharge and laser machining, the subsurface of these tools is strongly stressed mechanically and thermally. This also changes the residual stress state in the highly loaded cutting edge area. The measurement of these residual stresses is not possible by established XRD methods due to the highly curved surface of the cutting edge. The measurement method Raman spectroscopy shows high potential for this application, but conversion factors are necessary for the application. These factors enable the conversion of the stress-induced peak shift in the Raman spectrum into absolute residual stress values. Previous conversion factors are mainly based on hydrostatic load cases, which, however, cannot be transferred to the application on cutting tools. In this work, axial load cases were provided by bending and conversion factors were determined by comparing XRD stress measurements and Raman peak shifts. The conversion factors determined were then plotted against existing results from other studies and the causes for the deviations that occurred were determined. By this, for the first time, a conversion factor for an axial load case for cubic boron nitride could be determined and it could be shown that, as for diamond, it differs significantly from the hydrostatic load case.
Organisationseinheit(en): Institut für Fertigungstechnik und Werkzeugmaschinen
Typ: Artikel
Journal: Forschung im Ingenieurwesen/Engineering Research
Band: 88
Anzahl der Seiten: 8
ISSN: 0015-7899
Publikationsdatum: 11.03.2024
Publikationsstatus: Veröffentlicht
Peer-reviewed: Ja
ASJC Scopus Sachgebiete: Ingenieurwesen (insg.)
Elektronische Version(en): https://doi.org/10.1007/s10010-024-00726-6 (Zugang: Offen)

BibTeX

@article{9264098dcfdb4aeb972f0d955dd390d2,
title = "Locally resolved stress measurement in the ultra-hard composites polycrystalline diamond and polycrystalline cubic boron nitride",
abstract = "Cutting tools made of the ultra-hard composites polycrystalline diamond and polycrystalline boron nitride are being used in more and more sectors of machining. Due to the laborious preparation processes such as grinding, brushing, electrical discharge and laser machining, the subsurface of these tools is strongly stressed mechanically and thermally. This also changes the residual stress state in the highly loaded cutting edge area. The measurement of these residual stresses is not possible by established XRD methods due to the highly curved surface of the cutting edge. The measurement method Raman spectroscopy shows high potential for this application, but conversion factors are necessary for the application. These factors enable the conversion of the stress-induced peak shift in the Raman spectrum into absolute residual stress values. Previous conversion factors are mainly based on hydrostatic load cases, which, however, cannot be transferred to the application on cutting tools. In this work, axial load cases were provided by bending and conversion factors were determined by comparing XRD stress measurements and Raman peak shifts. The conversion factors determined were then plotted against existing results from other studies and the causes for the deviations that occurred were determined. By this, for the first time, a conversion factor for an axial load case for cubic boron nitride could be determined and it could be shown that, as for diamond, it differs significantly from the hydrostatic load case.",
author = "Bernd Breidenstein and Nils Vogel",
note = "Funding Information: s The authors would like to thank the German Research Foundation (DFG) for funding research project BR 2967/22-1 “Influence of preparation-induced residual stresses in the cutting edge of cutting tools on the wear behavior of extremely hard cutting materials.” Furthermore, the authors would like to thank the company Element Six for providing the cutting materials.",
year = "2024",
month = mar,
day = "11",
doi = "10.1007/s10010-024-00726-6",
language = "English",
volume = "88",
journal = "Forschung im Ingenieurwesen/Engineering Research",
issn = "0015-7899",
publisher = "Springer Verlag",
number = "1",
}